Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Crenshaw
Gate repair in Crenshaw usually costs $180 – $850 depending on whether we’re re-welding an original iron hinge, replacing a corroded control board, or straightening a slide gate that’s jumped its track. Most jobs on this side of town take one visit because the gate stock is older but straightforward: 1940s – 1960s wrought-iron swing gates, chain-link driveway sliders, and the occasional apartment barrier arm. We know these blocks, from the stucco bungalows off Crenshaw Boulevard to the low-rise courts closer to Morningside Park. Call (855) 360-4375 and we’ll give you a straight answer on what you’re dealing with. We answer 24/7. Fast dispatch from 7am to 7pm.
Why Crenshaw Homeowners Call Gate Repair Lynwood for Gate Repair
Most of the gates in Crenshaw have been repaired before. Some have been re-welded two or three times, and the homeowners we talk to would rather keep a solid original gate than pay for new steel that doesn’t match the house. That’s the work we do well. Dan Bannister runs Gate Repair Lynwood, and we’ve spent fifteen years as gate-only specialists, since 2011. We’re not a garage door shop that takes gate calls on the side. When you tell us your Mighty Mule keypad is faulting or your FAAC arm won’t cycle, we know the exact board we’re looking for before we pull up.
We service nine gate system brands across Crenshaw, and our technicians carry parts for the ones that fail most often out here: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The marine layer that rolls through these streets does predictable things to gate electronics and welds. We’ve seen enough Crenshaw gates to know what fails first and what’s worth saving. That’s what makes the repair cost sensible instead of a replacement quote you didn’t want.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Sliding Gate Repair in Crenshaw
Sliding gate repair in Crenshaw often starts with the gate dragging or stalling halfway across the driveway. On the 1940s – 1960s lots here, that generally means the track has shifted, the rollers are shot, or the rack and pinion has worked loose from years of coastal moisture settling into the mounting points. A typical sliding gate repair in Crenshaw runs $220 – $700. If the operator motor is also failing, you’re looking at the higher end. We quote the full price up front, before any work starts, so the number we agree on is the number on your invoice.
Track and Roller Repairs
Salt air doesn’t just eat the gate panel. It gets into the roller bearings and the track bolts. We replace seized rollers, clear rust from the rail, and reset the track so the gate rolls clean instead of shuddering at the halfway point. If your gate has jumped the track entirely, don’t force it back. The panel is heavy and a misaligned slide gate can come off its guide and pin someone.
Operator and Limit Switch Faults
When a slide gate opens halfway and stops, the limit switch is a common culprit. But along the coast, we also find control boards with corroded terminals from marine-layer moisture. We test the board, the photocells, and the motor draw before replacing anything. On a LiftMaster slide operator in Crenshaw, that diagnosis process usually takes under an hour, and the fix is often a sensor realignment rather than a full board swap.
Wrought Iron Gate Repair in Crenshaw
Wrought iron gate repair in Crenshaw is less about new metal and more about saving what’s already there. These original gates, many of them dating back to when these stucco homes were built, have real character. They also have layers of old paint, old weld beads, and sometimes rust so deep inside the hinge post that the panel is hanging by habit. A typical wrought iron repair runs $180 – $650, depending on how much metal has to be cut out and rebuilt. If the gate can be saved, we save it.
Hinge Collar and Post Repairs
The first thing to go on these gates is the hinge-post weld collar. Water creeps under flaking paint, the steel inside turns to scale, and the hinge pulls out of the post. We cut away the corroded section, bevel the remaining steel, weld in a fresh collar, and swap the old hardware for stainless fixings that actually hold up near the coast. The weld gets spot-primed and painted to match the surrounding ironwork.
Realigning and Straightening Panels
A sagging iron gate doesn’t always need new hinges. Sometimes the post has settled, sometimes the top rail has bowed, sometimes the latch side has worn enough that the panel binds on the strike. We measure the reveal, check the post plumb, and straighten or shim what needs it. You get a gate that latches without lifting the handle and closes with a click instead of a scrape.
Trusted Brands We Service in Crenshaw
We work on your brand. Whether it’s a Mighty Mule on a driveway swing gate or a FAAC operator at a commercial entrance off Crenshaw Boulevard, our techs know the system before they open the panel. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule across Crenshaw and keep common boards, photocells, and receivers in our local stock. That means fewer return trips and shorter waits when a board fails. From the motor to the control board, we diagnose and repair the whole system, not just the part that happened to be visible when you called.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Crenshaw Homes
- Hinge-post weld collars corroding from the inside. Original wrought-iron gates in Crenshaw hold moisture under layered paint, and the collar rusts through while the gate body still looks fine. We see this on swing gates all over the residential blocks near Vermont Vista.
- Control boards faulting from marine-layer moisture. Salt-laden air gets into operator housings and keypad entry units, causing intermittent open/close faults that look mechanical but are actually electrical. The board gets tested before anything gets replaced.
- Seized latch and hinge hardware on older gates. Decades-old chain-link and driveway gates in Crenshaw often have hinges so rusted the gate travel jams, which puts extra strain on the rack and pinion or the swing arm. We free them up or swap to stainless.
- Mechanical gates that have been re-welded multiple times. Many gates along these streets show evidence of two or three prior repairs. Matching existing metalwork and reusing salvageable hardware is usually more important than a full replacement.
Pricing for Gate Repair in Crenshaw, CA
Gate repair in Crenshaw typically runs between $180 and $850 for most jobs we quote. A latch replacement on a chain-link gate sits at the lower end. A wrought-iron hinge collar rebuild with fresh welds and paint matching lands around $350 – $650. Slide gate track realignment with roller replacement usually runs $220 – $450, and if we’re replacing an operator control board on a LiftMaster or FAAC system, you’re likely in the $400 – $850 range depending on the board and the extent of the corrosion damage. The estimate is free. We look at your gate, we tell you what’s wrong, we give you a written number, and that price is set before anything gets taken apart. Call (855) 360-4375 to schedule a time for us to come look.
No maintenance plans. No service contracts. You call when the gate acts up, we come out and fix it, and you pay the price on the written estimate. That’s the whole arrangement.
We Also Serve Cities Near Crenshaw
Our shop is based in Lynwood, and we run calls into Crenshaw every week. The same crew also covers Morningside Park to the south, Vermont Vista to the east, and Lawndale and Willowbrook nearby. If you’re right over the border in one of those neighborhoods, the response time is about the same and the pricing doesn’t change. Call (855) 360-4375 and we’ll get you on the schedule.
Serving Crenshaw, CA – Our Local Coverage Area
We serve Crenshaw and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Crenshaw
Salt air and marine-layer moisture from the coast settle into the paint layers and weld seams on old iron gates, and that corrosion happens noticeably faster in Crenshaw than in neighborhoods ten or fifteen miles inland. The hinge-post weld collars go first, because water sits inside them under flaking paint. If you want a repair that lasts, the fix is stainless hardware and a proper paint seal on the weld, not another layer of spray paint over the rust. Call (855) 360-4375 and we’ll tell you honestly whether your gate is worth saving.
Often yes. A sagging gate panel can usually be straightened, but whether the fix holds depends on what’s causing the sag. If the top rail is bowed from impact, we can apply controlled pressure and sometimes add a brace. If the post has settled or the hinges are worn, straightening the panel alone won’t hold. We diagnose the root cause first and then fix the whole gate correctly, which is usually less expensive than replacing the panel. The written estimate covers the full repair before we start.
Most automatic gate systems in Crenshaw are required to have safety photocells or edge sensors that stop or reverse the gate when people or vehicles are in the travel path. Every city’s building department enforces this differently, so confirm the local requirement with the City of Los Angeles or your HOA if you’re in one. We test the existing safety system on every automatic gate repair and will tell you if yours isn’t working, because a gate that closes on someone is both a safety and a liability problem. Estimates are free.
Yes, and in Crenshaw that’s usually the smarter route. Your original gate is likely better steel than anything you can buy at a home center today, even after sixty years. We match the metal thickness, the scrollwork where possible, and the paint color so the repair blends in rather than standing out. Between the rust and the layers of old paint, many of these iron gates can be rebuilt and re-hung for a fraction of the cost of a new custom gate. Call (855) 360-4375 for a free on-site estimate.
It’s more often corrosion from marine-layer moisture than a failed motor. Salt air settles into the operator housing and corrodes the control board terminals, which causes intermittent faults that look like motor problems. We bench-test the board and measure motor draw so we can tell you exactly which component failed and replace only what’s dead. On slide gate systems in Crenshaw, that approach saves you real money compared to swapping a motor that was never the problem in the first place.
Written by Dan Bannister, Owner at Gate Repair Lynwood, serving Crenshaw since 2011.