Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Lynwood?
A gate motor or opener replacement in Lynwood usually runs $650 to $2,400 for the operator and installation, depending on whether it’s a residential swing gate or a commercial slide gate. A new motor for an existing residential system typically lands between $650 and $1,200, while full operator replacement on a commercial slide or barrier-arm system runs $1,400 to $2,400 or more. These are estimates for the Lynwood market in 2026; the written estimate we provide after we look at your gate sets the final price.
We’re gate-only specialists. Every job we take is a gate job, which means the technician who shows up already knows the difference between a Mighty Mule on a residential driveway and a FAAC system at a commercial entrance. Whether your operator has failed completely or it’s behaving in ways you can’t explain, we diagnose from the motor to the control board and get you back up and running.
Key Takeaways
- Residential gate motor replacement in Lynwood: typically $650-$1,200 for the operator and labor.
- Commercial slide and barrier-arm operators: typically $1,400-$2,400.
- Diagnostic visits are free; the written estimate sets the final price.
- We work on nine major brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Same-day service is often possible; call (855) 360-4375 for scheduling.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the numbers break down for common gate motor and opener work in Lynwood. These ranges reflect operator cost plus installation labor for a typical residential or light commercial job. Your written estimate will show the exact figure for your gate.
| Line item | Typical range in Lynwood |
|---|---|
| Residential swing gate operator (Mighty Mule, Ghost Controls class) | $650 – $1,100 |
| Residential slide gate operator (Linear, Viking class) | $900 – $1,500 |
| Commercial slide gate operator (FAAC, BFT, DoorKing class) | $1,400 – $2,400 |
| Barrier-arm operator (parking lots, commercial entrances) | $1,600 – $2,600 |
| Control board replacement | $250 – $550 |
| Safety sensor / photo-eye replacement (pair) | $180 – $400 |
| Remote / keypad / receiver reprogramming or replacement | $100 – $300 |
| Wiring repair (power or low-voltage loop) | $200 – $600 |
| Full new gate + operator installation | $3,500 – $8,000+ |
What pushes a gate motor or opener job toward the higher end of these ranges? Three things: the drive type (commercial slide operators cost more than residential swing), whether the control board is part of the failure, and whether wiring needs to be run or re-run. A W-2 class operator with reversing sensors and a battery backup costs more than a basic residential arm. If you’re starting from a manual gate and adding automation for the first time, the gate itself may need reinforcement or a different mounting configuration, which adds to the total. We figure all of that into the estimate before we quote, not after.
Jobs vary. Sometimes it’s a straight operator swap on a Linear system that’s been running for years. Other times we find the motor is fine and the problem is a control board fault or a sensor that’s been tripping for weeks. The catch is that diagnosis comes first. Until we’re on-site, we can’t tell you which parts you actually need, and we won’t sell you a motor you don’t need.
What Affects Gate Motor & Opener Pricing in Lynwood
- Gate type and drive system. A swing gate operator and a slide gate operator are different animals with different price points. Swing gates usually run less for residential; slide gates add cost with track hardware and travel length. Barrier-arm systems for parking lots sit at the top. We work on all three.
- Brand and model family. A Mighty Mule or Ghost Controls replacement is a different price tier than a FAAC or DoorKing commercial unit. We work on your brand specifically, which means we recognize it on sight and don’t waste time figuring out what you’ve got. That saves you labor hours, which is the biggest variable on any job.
- Control board versus motor failure. A failed control board costs less than a full motor replacement. A motor that’s gone bad but damaged the board along the way can double the parts bill. Accurate diagnosis is the difference between those two outcomes.
- Wiring and power conditions. If the low-voltage loop back to the house has been chewed or corroded, or if the power feed to the operator needs to be re-run, that’s extra labor. Lynwood properties with older concrete and landscaping mean we sometimes find buried wiring in worse shape than expected.
- Safety accessories. Photo-eyes, reversing edges, and loop detectors are often required on commercial systems and are standard on many residential installs. These add to the total but are part of a complete working system, not an upsell.
- Gate hardware condition. A motor is only as good as the gate it drives. If the hinges are binding, the track is bent, or the gate is sagging, the operator can’t do its job. We’ll flag those so you’re not paying for a new motor that fails in six months.
Lynwood’s climate is mild, which is actually kind to gate hardware. We don’t see the freeze-and-thaw stress that tears up operators in colder regions, and we don’t see heavy snow loads. What we do see is dust and grit, especially on properties near busy streets or light-industrial areas, and that finds its way into tracks and gears over time. That’s part of why regular inspection matters more than any weather-driven replacement cycle here.
How to Save on Gate Motor & Opener
The biggest cost saver is diagnosing the right part the first time. If you call a general handyman who guesses, you can end up paying twice. We’re a gate specialist, so we’ve seen your failure mode before on the same brand, whether it’s a LiftMaster control board or a Viking motor that’s drawing too much current. That expertise is what keeps the labor hours down.
A few practical things you can do:
- Don’t wait on a slow gate. A gate that’s getting sluggish or sticking is usually telling you a hinge, track, or gear is failing. Fixing that early costs less than replacing a motor that burned out working against resistance.
- Get the whole system looked at at once. If the motor is dead, have the technician check the sensors, wiring, and gate hardware in the same visit. A second trip is a second labor charge.
- Match the operator to the gate. A commercial-grade operator on a residential driveway is usually overkill; a residential arm trying to move a heavy slide gate will wear faster and cost you more in the long run. We size the operator to the gate honestly.
- Ask what’s under warranty. Many operators carry a manufacturer warranty on the motor and board. We’ll tell you what’s covered so you can weigh repair against replacement with real numbers.
- Start with a free estimate. There’s no charge to have us look at your gate and put a written price in front of you. Call (855) 360-4375 to schedule.
For customers working through a repair versus replace decision, the math usually favors repair when the operator is under ten years old and only one component has failed. When the motor, board, and sensors are all failing at once, a new operator is often the better value. We’ll give you both numbers and let you decide.
FAQs – Gate Motor & Opener Cost
How much does a gate motor cost in Lynwood?
A gate motor in Lynwood typically costs $650 to $1,200 for residential systems and $1,400 to $2,600 for commercial slide or barrier-arm operators, installed. The operator itself plus installation labor makes up most of the price. Call (855) 360-4375 for a free estimate on your specific gate.
Should I repair or replace my gate operator?
Repair usually makes sense when the operator is under about ten years old and only one part has failed, at a typical cost of $250 to $600 for a board, sensor, or wiring fix. Replace when the motor and board are both failing or the unit is well past its service life. We’ll give you both numbers so the comparison is honest.
Can you come today?
Same-day service is often possible when you call early. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (855) 360-4375 and we’ll get you scheduled.
Do you work on my brand of gate operator?
Yes. We work on nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers everything from a residential Mighty Mule on a driveway to a commercial FAAC system at an entrance gate.
Does a new gate opener require a permit in Lynwood?
Permit requirements vary by gate type and whether new electrical service is being added, so the honest answer is to check with the city of Lynwood building department before the work starts. Ask us your questions first, call (855) 360-4375, and we’ll walk you through what typically needs a permit.
Get a Free Estimate on Your Gate Motor or Opener
Gate Repair Lynwood has been serving Lynwood and the surrounding area since 2011, and we’re gate-only specialists. Every technician on our crew has the tools, parts knowledge, and diagnostic habits specific to gate systems, so your operator gets fixed by someone who already knows a FAAC motor from a Linear board and can tell what’s failing from the symptom. We diagnose the full system from the motor to the control board, and we install new operators for property owners starting from a manual gate. Whether you’re a homeowner, landlord, HOA manager, or commercial property owner, call (855) 360-4375 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Lynwood, serving Lynwood since 2011.
Pricing reflects the Lynwood market as of 2026. Gate Repair Lynwood offers free estimates – call (855) 360-4375.
What Our Customers Say
"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Maria Castillo"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Omar Hassan"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Alejandro Vargas