Gate Company in Maywood - Same-Day Service, Priced Before We Start

Gate Company in Maywood, CA

Gate installation in Maywood is rarely a matter of unboxing a standard panel and setting two posts. Most of our work here involves custom sizing a gate for a narrow 25 to 40 foot frontage, a rear alley apron, or a block-wall opening that was never built square to begin with. The housing stock is older, the lots are tight, and the alleys see real traffic, which means the gate has to survive being grazed by trash trucks and still swing true. If you need a gate built, repaired, or automated in 90270, call (855) 360-4375. We answer 24/7.

Call (855) 360-4375

Why Maywood Homes Are Different

Maywood’s residential grid is one of the densest in Southeast LA County, and that density changes how gates get built and repaired. The typical lot sits between 5,000 and 6,000 square feet, but many have been subdivided over the decades, leaving frontages that run 25 to 40 feet wide with a driveway squeezed alongside the house. A gate that would swing comfortably in a newer suburb often has no room to travel here, so we frequently re-engineer the hinge geometry, shorten the leaf, or convert a swing gate to a slide configuration that hugs the property line. Rear alleys function as a second street throughout Maywood, with gates opening directly onto shared aprons. Those alley-facing gates take a beating from delivery trucks and refuse vehicles, and a “won’t close” call very often traces back to a gate that was struck backing out of an alley garage. The housing itself is mostly 1920s through 1950s Spanish-style and stucco box bungalows, many with block-wall perimeters and metal gates set into masonry pilasters. Those pilasters were poured decades ago, and we regularly find the embedded posts have shifted enough to throw a gate out of level.

The climate does its part too. Summers are dry and sun-baked, which fades painted steel and bakes lubrication out of hinges. Winters are mild, but seasonal dew collects at welds and speeds up rust exactly where the gate carries its load. The dry-wet cycle also moves the ground under older concrete aprons, and a cantilever or sliding gate that ran fine in spring can bind by fall. None of this is unusual to us. It is what a Maywood gate job looks like.

Our Main Maywood Services

Most calls we take in Maywood fall into two categories: a gate that has stopped working, and a gate that never worked right to begin with. Here is what each involves.

Gate Repair in Maywood

Gate repair in Maywood usually starts with a gate that drags, sags, or will not latch because a hinge or post has given out after years of tight-clearance use. We see a lot of weld failures on steel gates here, particularly at the hinge-side frame where repeated stress in a confined swing arc concentrates load. The repair work covers everything from replacing seized hinges and welded-on posts to straightening a leaf that a trash truck clipped in the alley. Most jobs are quoted and completed for far less than a full replacement, and we will tell you straight if the frame has rusted past the point where welding makes sense. Learn more on our Gate Repair in Maywood page.

Electric Gate Repair in Maywood

Automated gates in Maywood fail for predictable reasons: dust gets into the operator, the control board takes a voltage hit, the safety sensors drift out of alignment, or the gate itself starts binding and trips the overload. Our technicians diagnose the full chain, from the motor to the control board to the photo eyes, and we work on the brands most common around here, including LiftMaster, FAAC, BFT, and Mighty Mule. A gate that opens but will not close, or cycles halfway and reverses, usually has a diagnosis we can make on the first visit. That is the core of our Electric Gate Repair in Maywood service.

Gate Installation in Maywood

Gate installation in Maywood is built around a simple reality: nearly every opening here is a custom size. The narrow 25 to 40 foot frontages and frequent rear-alley access mean an off-the-shelf panel from a big-box store almost never fits the pilaster spacing, and a gate that cannot travel its full arc is a gate that will fail early. We measure the actual opening, check the footing depth at both sides, and build or order a gate sized to the space, not the other way around. From manual driveway gates to fully automated alley entrances, this is what we do every day. See our full Gate Installation service details.

Automatic Gate Installation

Signs you need it

You are getting out of the car to open and close the gate every time, or you have stopped using the driveway entirely because the manual swing is too heavy or awkward on a narrow Maywood frontage.

What it costs in Maywood

Automatic gate installation in Maywood typically runs from $3,500 to $10,000 depending on the gate material, operator brand, and whether we are adding an intercom or keypad, with commercial slide systems at the higher end.

How we do it

We survey the opening, pour or reinforce the operator pad, mount the arm or slide track, hang and balance the gate, wire the control board, and run full open-close cycles with the safety edges and photo eyes in place before we hand it over.

Driveway Gate Installation

Signs you need it

The current gate sags into the driveway, scrapes on the concrete, or leaves a gap wide enough that the gate is more decoration than barrier.

What it costs in Maywood

Driveway gate installation in Maywood generally falls between $2,800 and $7,500 for a steel or wrought-iron look gate, with custom fabrication on tight lots adding to the final quote.

How we do it

We set new posts into the existing pilasters or pour fresh footings, fabricate or order the gate panel to the measured opening, hang it with adjustable hinges, and set the latch and stop so the gate closes solid every time.

Sliding Gate Installation

Signs you need it

The driveway has no room for a swing arc, or the current swing gate keeps getting hit because it intrudes into the alley or the street-side turn.

What it costs in Maywood

Sliding gate installation in Maywood is typically $3,500 to $9,000, with the track system, gate weight, and cantilever hardware driving most of the price difference.

How we do it

We lay a level track or build a cantilever frame, mount the gate rollers, hang the panel, and adjust the travel stops and guide rollers so the gate slides clean without binding on the older concrete aprons common in 90270.

What Gate Installation Costs in Maywood

Here is the pricing breakdown we quote from. The final number always comes from the written estimate after we measure in person.

How much does a gate cost in Maywood?

A manual driveway gate in Maywood typically runs $2,800 to $7,500 installed, and an automated gate runs $3,500 to $10,000 depending on operator brand and gate size. Tight lot clearances and custom fabrication push quotes toward the upper end. Call (855) 360-4375 for an exact quote, free of charge.

Do you handle the power and safety sensors?

Yes, the full installation includes the power run to the operator, the photo eyes, safety edges where needed, and all control wiring. We will not install an automatic gate without working safety devices. Call (855) 360-4375 to schedule a free on-site measure.

Brands We Service in Maywood

We are gate-only specialists, and over 15 years in the trade that focus has built deep familiarity with the brands Maywood property owners actually have. Our technicians work on LiftMaster and Mighty Mule residential operators, FAAC and BFT commercial systems, and the swing, slide, and barrier-arm configurations that come with them. Most common control boards and arms are available locally, which keeps repair turnaround short. See our brands for the full list.

Pricing for Gate Company in Maywood, CA

Neighborhoods We Serve in Maywood

We work the full 90270 ZIP, from the streets closest to Atlantic Boulevard over to the alley-lined blocks south of Slauson. The gate systems here are a mix of 1950s steel, newer chain-link, and the occasional heavy automated slider on a commercial lot.

• Maywood Central
• South Maywood
• Alameda Corridor area
• Neighborhoods off Atlantic Boulevard
• East Maywood

Most of our Maywood calls get a same-day visit when a gate is down, and we dispatch from 7am to 7pm, Sunday through Friday.

Service Area – Cities Near Maywood

Gate Repair Lynwood runs crews throughout Southeast LA County, and Maywood sits right in the middle of our normal route. If your property is on the edge of town, we also cover Bell Gardens, CA, Central-Alameda, CA, Watts, CA, and Fashion District, CA. Call (855) 360-4375 and we will tell you exactly when a technician can be there.

FAQs About Gate Company in Maywood