Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across San Gabriel
When an electric gate stops working in San Gabriel, the problem is almost always in the operator, the control board, or a safety sensor, not the gate itself. Most repairs take one visit because we keep common LiftMaster, FAAC, and Viking components on the truck. We know San Gabriel’s streets, from the historic blocks east of Mission Drive to the mid-century ranch neighborhoods further out, and we dispatch a gate-only technician fast from 7am to 7pm, Sunday through Friday. Call (855) 360-4375 and you’ll reach a person, not a call center. We answer 24/7.
Why San Gabriel Homeowners Call Gate Repair Lynwood for Electric Gate Repair
At Electric Gate Repair, we work exclusively on gates. That is the whole job. When a homeowner in San Gabriel calls us about a gate that will not open, the technician who shows up diagnoses gate motors, control boards, and sensors all day, every day. He is not squeezing a gate call between a garage door spring and a water heater.
Dan Bannister has built the company around a simple idea: recognize the system, then fix it. A LiftMaster operator on a heavy ornamental swing gate behaves differently from a BFT slide operator on a commercial driveway in San Gabriel, and we treat them as different jobs. Homeowners here appreciate that we name the brand on the phone before we arrive, because it means the first visit usually ends with the gate working.
We have been doing this since 2011. Fifteen years of nothing but gates gives a technician diagnostic habits that a generalist never develops. The result for San Gabriel property owners is fewer return trips and a repair that holds.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Access Control in San Gabriel
Gate Access Control in San Gabriel usually means a keypad, an intercom, or a telephone-entry system wired into an automatic gate operator so only authorized people get in. On the historic properties around the Mission, we often see older access systems that need to be matched to the existing gate rather than replaced with something modern that looks wrong.
For a typical single-family driveway gate in San Gabriel, repairing or replacing a keypad runs $220 to $480. Adding or replacing a telephone-entry intercom on a residential property typically lands between $450 and $900. If the access control failure is on the operator side, for example a bad receiver board, the repair is usually $180 to $380 depending on the operator. Commercial systems with multiple tenant codes and a telephone interface run higher, typically $800 to $1,800, because the integration work is heavier. Every price is set by a written estimate before any work starts, and the estimate is free.
Intercom and keypad repair on older gates
On an older electric gate repair job in San Gabriel, the access hardware can be decades old. Wiring connections corrode, keypads fail from sun exposure, and we frequently rebuild the connection between the keypad and the operator board without replacing the gate itself.
Adding access control to an existing gate
A San Gabriel homeowner who already has a manual gate sometimes wants to add an operator and a keypad at the same time. That is a measured job, quoted after we look at the gate, its weight, and how it is hung. We set the price in writing before we order anything.
Commercial Gate Operator in San Gabriel
Commercial Gate Operator work in San Gabriel concentrates on apartment buildings, church parking lots, and small commercial lots where a slide or barrier-arm gate controls vehicle access. These operators run more cycles in a week than a residential gate runs in a month, so the failures are different: burned contactors, worn limit switches, and control boards that stop responding after a power event.
A commercial slide gate operator repair in San Gabriel typically runs $650 to $1,400, depending on the brand and what has failed. Replacing an entire commercial operator, including removal of the old unit and setup of the new one, usually falls between $2,800 and $6,500. Barrier-arm systems run lower on parts but the labor is similar. We service FAAC, BFT, Linear, and Viking commercial operators, among others, and we can often have a failed unit running the same day we diagnose it. The written estimate sets the final price, and you approve it before we order parts.
Slide gate systems and rack-and-pinion failures
Slide gates in San Gabriel fail most often at the rack and pinion or at the limit switch that tells the operator when to stop. When a slide gate stops mid-travel, the operator is frequently fine; the drive mechanism or the sensors are not.
Barrier arm and parking lot gates
Barrier arms take abuse. Vehicles hit them, wind loads them, and the internal spring or counterweight eventually gives out. We replace arms, rebuild the operator head, and align safety loops so a barrier arm stops and reverses correctly.
Trusted Brands We Service in San Gabriel
Our team is familiar with the brand-specific failure patterns on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. In practice, that means a San Gabriel homeowner with an old Viking slide operator gets a technician who already knows how that operator’s limit switches behave, instead of someone reading a manual in the driveway. We keep common Linear and FAAC control boards and remote receivers in local stock, and we can source period-correct hardware faster because we are not learning the brand for the first time. From the motor to the control board, we work on your brand.
Common Electric Gate Repair Problems We See in San Gabriel Homes
- Sagging ornamental iron gates on original hinges. Many Mission District gates hang on original 1920s cast hinges. Santa Ana winds work the heavy leaves until the hinge wallows out, and the panel sags at the hinge post rather than in the middle. We rebuild the hinge in period-correct iron, not with stock hardware.
- Wet-winter rust seizing slide gates. San Gabriel’s mild, wet winters rust original iron hardware and rot the stiles of older wood gates. A rusted rack and pinion binds a slide gate, and the operator stalls or trips its overload protection.
- Sun-warped wood gates tripping photocells. Mid-century ranch homes often have wooden gate leaves that warp in the hot, dry summers. A warped leaf breaks the safety photocell beam, so the operator reverses on its own and refuses to close. The fix is usually a rehung leaf and a photocell realignment.
- Control board failures after power surges. Older San Gabriel neighborhoods have mature trees and occasional substation surges. A surge can brick a control board, and the symptom is a dead keypad and a gate that will not respond to any remote. We test the board before replacing the whole operator.
See the difference
Before
After
Before
After
Before
AfterPricing for Electric Gate Repair in San Gabriel, CA
For a typical electric gate repair in San Gabriel, a service call and diagnosis lands between $90 and $150, and most component-level repairs add $150 to $400 on top of that. A control board replacement for a residential operator runs $250 to $550; a commercial board is $500 to $1,100. Opener motor replacement is usually $350 to $800 for residential and $900 to $2,200 for commercial slide operators. New gate operator installation, including the operator, brackets, and setup, typically runs $1,600 to $4,800 for residential and $3,000 to $7,500 for commercial systems. Heavier ornamental gates and custom fabrication for historic hardware add to the job, which is why we quote after a site visit. Every estimate is free, and the written estimate is the price. On repair calls, you approve the number before we turn a wrench.
We Also Serve Cities Near San Gabriel
Our gate technicians cover the surrounding San Gabriel Valley and central Los Angeles, including Chinatown, Downtown Los Angeles, Little Tokyo, and Maywood. If your property sits near the Mission or up toward the 10, call (855) 360-4375 and we will confirm a dispatch window. We answer 24/7, and dispatch runs Sunday through Friday, 7am to 7pm.
Serving San Gabriel, CA – Our Local Coverage Area
We serve San Gabriel and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in San Gabriel
Yes. When a historic gate in the Mission District needs new scrollwork or a rebuilt hinge, we fabricate replacement pieces in period-correct profiles rather than welding on modern stock. That keeps a 1920s wrought-iron gate consistent with San Gabriel’s preservation guidelines and with the rest of the streetscape. Call (855) 360-4375 for a free on-site estimate; we will tell you what can be repaired in place and what must be refabricated.
Usually the post. On heavy ornamental gates, the hinge post footing settles over time and the original cast hinge wallows out, which makes the panel drag. We reset the post footing, rebuild the hinge, and then test the operator and safety sensors before we leave. The written estimate we give before starting covers the foundation work, the hinge, and the operator setup.
The two things to check are the reverse mechanism and the photocell pair. On a working gate, the operator should reverse when it meets resistance, and the photocells should stop and reverse the gate when the beam is interrupted. If either has been bypassed or ignored, the gate is unsafe, especially around children and pets. We test both on every repair visit and will show you what we found. Call (855) 360-4375 if you want a gate checked before an accident happens.
We service underground operators on residential swing gates and above-ground operators on slide and barrier-arm systems. That includes LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Underground operators fail less often, but when they do, the repair usually involves digging out the box, replacing the motor or the drive, and resealing it against San Gabriel’s wet-winter soil. Free estimates every time.
Yes. The combination of hot, dry air and sustained wind works the hinges and fasteners on older gates, especially heavy ornamental iron. Loose hinges let a panel sag and bind, which shortens operator life and wears out limit switches. We recommend checking hinge bolts and post plumb after a strong wind season, and we can do that on a repair visit. Call (855) 360-4375 to book a check. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday.
Call Gate Repair Lynwood for Electric Gate Repair in San Gabriel
If your gate is dead, stuck open, or noisy, call (855) 360-4375. We answer 24/7, and a gate-only technician can be dispatched to San Gabriel from 7am to 7pm, Sunday through Friday. We will diagnose the motor, the control board, or the sensor that failed, quote you a price in writing, and get the gate back up and running. Free estimates, and you approve every repair before we start.
Written by Dan Bannister, Owner at Gate Repair Lynwood, serving San Gabriel since 2011.